Product Description
Small Peanut Oil Presser Machine Stainless Steel Made to Last High Oil Yield
About Screw Oil Press:
Screw oil press works by physical squeezing,with obvious advantages of low investment,high oil yield,easy to operate,easy to maintain and wide application ,e.g peanut,rapeseeds,soybeans,cotton seeds,tung seeds,palm kernels etc
Application:
This screw oil press is advanced expeller which is widely used in pressing oil from vegetable oil seeds, such as soybean, peanut, sunflower seeds, cotton seeds, sesame, tea seeds, copra, jatropha seeds, castor seed, etc. And the product oil is for both edible and biodiesel fuel purpose. It has advantage of high efficiency, low consumption, simple operating, stable function, easy maintenance, high productivity and high oil output.
Advantage
1.Simple and easy operation,one key to start without other operating
2.The residual oil content does not exceed 7 percent
3.Reliable transmission systems are mostly helical gears with greater torque
4. Pure copper motors are more powerful and less failure rate
5. Reasonable design and configuration of strip and round row ensure faster oil output and higher oil yield
6. Stainless steel oil guide plate is cleaner and more sanitary
7 Advanced automatic stirring forced feeding system ensures the uniformity and continuity of feeding
8.Convenient and labor-saving adjustment and disassembly system facilitates product adjustment and maintenance
Structure:
The machine consists of five main parts: the feeding hopper, gearbox, press cylinder, screw and machine frame, as shown in the figure.
Machine Operation
1 preparations before operating
1.1 12kg of lubricant needs to be filled into the gearbox.
1.2 After installing the machine, check whether lubricant has been filled in, bolts have been tightened, and handles are operable.
1.3 Check large pulley whether it is loose or blocked, repair it if necessary.
1.4 Adjust the tightness of the belt, switch on the motor and check its rotation direction.
1.5 Loosen the lock nut and tighten the screw to its end, then loose it for3-4circles and then tighten it again for half circle to assure the gap of the residue cake outlet.
2 Operating
2.1 Feeding must be steady and slow at the beginning to avoid blocking
2.2 In the case no cake is extrude outward,return back the screw for 1-2circle .If there is still no cake is observed,machine needs to be shut down and checked ,However, in any case, operating the machine backward is absolutely prohibited normally ,cake looks like tile but not sticky ;thickness is 1-2mm ,inner side is smooth ,out side creases and no oil the surface is allowed.
Cake thickness adjustment: Rotating the adjusting handle clockwise will make the cake thicker, otherwise will make it thinner. Each circle of adjustment (by adjustment bolt left hand T 165x6)will change the thickness 0.4-0.5mm.
2.3 When machine is operating, oil extruding and residue outlet need be checked
Frequently .Normally, most of oil will flow outward from square rods and several front round plates. Broken cake residue indicates the material is too dry; steam emerging from the cake residue indicates that it is too wet; In any case, water content in the raw material must be adjusted from time to time.
Slag slice emerging indicates too much water content and power-like slag low water content .Loose round plates will cause too much slag flowing outwards. However, adequate water content will cause slag flowing outwards from square rods; little slag from round plates is allowed. In a word, water content affects oil output rate, it needs adjusting properly.
3 stopping
3.1 Repeatedly move screw forwards and backwards for several times and let all material resided in the chamber goes out and adjust the cake to the possible thinnest, then stop the machine.
3.2 When machine stops caused by any accident, power supply must be shut down first, then rotate large pulley manually backwards, let the material return out. Then pull out the shaft and clean it. In the case the shaft could not be pulled out, remove the upper case and loose lock nut, separate round plates and clean them one by one.
Safety
Following items are strictly requested to be obeyed.
1 During operating, hands or metal rods are strictly prohibited to enter the hopper to touch cakes.
2 Tightening the screw shaft to its dead end is prohibited before starting or during operating, which might cause slag outlet to contact cake outlet ring, resulting in wearing.
In the case of storage, oil dirt on machines surface and slags on each part need to be taken off. Paint
rust-resisting grease and keep in dry place. Case needs to be covered to prevent dirty foreign particles from entering.
Factory Advantages:
Shenqiu Wanxiang Machinery Manufacturing Co.,Ltd has been a professional manufacturer of grain & oil machinery with advanced integration of research and design,and is specified by the National Industrial Machinery Ministry as the professional oil
extraction equipment factory,with a glorious 40- years expertise in the industry.
We always adhere to the principle of " reliable qual ity,reasonable price,timely del ivery,great aftersales service" ,and have till now established sound cooperation with customers from home and abroad. As our leading products,the 6YL series have won many industrial awards and worldly reputation.
The factory passed ISO9001 certification in 2000. Besides,we also manufacture complete oil pressing lines of capacity between 5 tons to 100 tons,including complete palm oil processing lines.
){kind=link}