| Customization: | Available |
|---|---|
| After-sales Service: | 24X7 After Sales Service |
| Warranty: | 3 Years for Main Structure |
|
Still deciding? Get samples of US$ 400/Piece
Request Sample
|
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
Standard Technical Parameters of 6YL-130-9ASeries Screw Oil Press Series:
| MACHINE | 6YLSERIES |
| MODEL | 6YL-130-9A |
| CAPACITY(T/M) | 10-12 |
| POWER(KW) | 18.5 |
| DIMENSIONS(MM) | 2150*700*1500 |
| OIL RESIDUE(%) | ≤7 |
| SHAFT SPEED(rpm) | 35-39 |
WEIGHT(KG) |
780 |
Preparation before startup
1.After installing the expeller, fill the lubricating oil according to the regulations, check whether the parts are fastened, and whether
the operation handle and insert plate are flexible.
2.Move the big triangle belt wheel by hand to make the machine rotate, check whether the moving parts are normal, whether there
is any foreign matter stuck in the press chamber, if not normal, it should be excluded.
3.Check and adjust the tightness of the belt.
4.loosen the anti-loosening nut, according to the direction of the arrow pointed to trigger the handle, so that the slag slightly head
and cake ring contact, and then return 3-4 turns, and then forward half a circle, to ensure that the slag slightly head and the gap
between the cake ring.
5.Start the motor, the direction of rotation of the big triangle belt wheel should be consistent with the direction of the mark (arrow).
Carry out the empty running test of the oil press, generally running for about half an hour. During the operation, you should pay
attention to the sound and temperature of the oil press, if you find any abnormal phenomenon, you should stop the machine to
check and eliminate.
Factors affecting oil output rate
Following factors may affect oil output rate:
1.Water content:This is the critical factor,as a matter of fact,water content directly affects oil output rateHowever, user usually has
not proper
inspection equipment.Hence,water content of some main raw material maybe detected as follows:
(1) Bean: if teeth beating could crack it,forming flat pieces accompanied with light sound the watercontent is suitable.Flat piece
without cracking means too wet.Heating or sunshine may be drive'wateroff.However,cracking accompanied with loud indicates
too dry. Adequate water needs to be added.
(2) Cotton seeds: shell and kernel may be separated by teeth beating. Shell breaking may be accompaniedby sound, which
means water content is suitable .shell being flatting indicates too wet, shell being splitted intopowder means too dry.
(3)Rape seeds: They can be pressed either at hot or at cold state. Cold pressing: extruding by finger, ifthey splitted into two
pieces, accompanied by sound and oil,this implicates water content is adequate.Otherwise,extruding makes power indicates
too dry; makes flat slice, too wet. Hot pressing (after heating) :Toscratch seeds by two slices of wood, if shell and kernel could
be splitted, water content is adequate. If kernelbecomes power, it is too dry; in the case that shell and can be splitted, it is too
wet.
2.Cakes thickness reflects the pressure inside the chamber. Thicker cake indicates lower pressure insidethe chamber; thinner
cake-higher pressure inside. If raw material has less oil content, chamber pressure shouldbe higher, cake will be thinner, round
plates need to be tightened; in the case of high oil content material,pressure in the chamber should be lower, then circular plates
need to be loosened, resulting in thicker cake.Recommended thickness of cakes will be.
Bean:1.1-1.Smm for the first time;0.5-1mm for the second time.
Cotton seeds : only one pressing,1-2mm.
Ground nut kernel : Normally cold pressing for 2-3 times,1-2mm
Important note: cakes thickness should be as according to different factors to achieve highest oil outputrate.Hence, above
figures will only be for reference.
Henan Winglobal Machinery a fully integreated factory enterprise of design, manufacturing and sales of oil presses. It is designated by the former Ministry of Industrial Machinery as the recognised oil press manufacturing base, with 40 years history till now.
We are proud of our sophisticated equipment and rich technical expertise. Guided by the principle of "Dependable Quality, Reasonable Price, Timely Delivery, Considerate Aftersales", we have established firm and ever growing relationships with customers both at home and abroad.
We passed ISO in 2000, and in 2008 we achieved CE certificate. With our strength, our oil press products come with less energy consumption, and best oil yield rate. The oil press can be used to squeeze oil from all types of granular or powder oil seeds, including soybean, peanut, sunflower seeds, tung seeds, mustard seeds, castor seeds, palm fruit, palm kernel/fibre, coconut, rapeseeds, moringa etc.
Apart from the above, we also manufacture the combined automatic oil press, auxiliaries of all sorts, palm oil processing complete line, oil refinery set and so on.
){kind=link}